Cisco PAP2T




If you are running the PAP2t with a tomato firmware router, this may represent a persistent issue after
rebooting the device, generally it won't register back as usual, in order to fix this you only need to set
Tomato UDP Unreplied timeout down to 10 (from default of 30).

Configuration Details

Step 1

The first step is to find out what IP Address your adapter is currently using. To do this, pick a phone connected on Line 1 and do the following:

Dial: **** (That is 4 asterisks)
Once this is done, dial: 110# (110 followed by a square)

The system should now playback the IP Address your device has been assigned.
(Example: 192.168.1.2)

 

Step 2

Using your favorite web browser from a computer on the same network, point the address to the IP address of your adapter.
(example http://192.168.1.2) Replace 192.168.1.2 by the IP Address your device is currently using.

 

Step 3

You should now see the web interface of your Linksys/Sipura.

At the top of the page below the tabs, click on the link "Admin", and once the page has reloaded, click again on the link "Advanced View".

 

Step 4

Under the LINE 1 Tab, Find the following fields and fill them with the following information

Nat Keep Alive: Yes
Nat Mapping/Traversal: Yes
Proxy: atlanta.icttech.net (You can choose any of our multiple icttech.net servers)
Register Expires: 180
Proxy Fallback Intvl: 180
Display Name: John Smith (Replace with your name or company name)
User ID: 100000 (Replace with your icttech.net username)
Password: ******** (Type in the account password)
Use DNS SRV: NO
DNS SRV Auto Prefix: NO

 

Step 5

You can configure your adapter with a better dial plan, allowing faster dialing of 10 digits number (Local US/Canada) and also enable 7 digits dialing in one area code of your choice.

At the bottom of Line 1 TAB, you will find a field called Dial Plan

Replace the 555 digits in the following line by the area code of your choice and copy the line, including parenthesis, in the Dialplan field in Line 1 Tab at the bottom of the page:

(911S0|310xxxx|<:1555>[2-9]xxxxxx|1[2-9]xx[2-9]xxxxxxS0|[2-9]xx[2-9]xxxxxxS0|*xx|***xxx|*xx.|[3468]11|822|0|00|4xxx|**275*x.|xxxxxxxxxxxx.)


Click here for more information on Linksys dial plans


Step 6

Click on the "Save Settings " button at the bottom of the form.


Configuration Screens

 

PAP2T Configuration Screen

 

PAP2T Configuration Screen

 

Customer Submitted Information:
For North America:
Found this link on configuring the PAP2-NA hardware to work better in North America and specifically with icttech.net.
Read the article called: Configure your Linksys VoIP ATA the right way!

To upgrade a firmware version from a Windows system, the PAP2T-NA documentation nor Cisco's web site does not say how to do this. Go to Cisco PAP2T Internet Phone Adapter with 2 VoIP Ports. Click on the link "Download Firmware", which downloads the .zip file. Run the .exe file, then enter the IP number of the ATA device (called “SPA” in the program). It then upgrades the device. This is provided for your information: the author is not saying you have to upgrade the firmware.

How to avoid the long delay to hear the ringtone

If you ever experience some delay to hear the ringtone when you make outgoing calls with your PAP2T. Changing the PAP2T's Interdigit Long Timer value can help resolve the issue. Follow the next steps in order to change that setting:

Note: However before changing that option, test if calling the number with an # at the end of the number works(e.g. 5554441234#). 
      If that doesn't work you need to contact the support staff in icttech.net.

 

  • 1- First access the PAP2T's web interface.
  • 2- Click on the Admin Login and then click on (switch to advanced view)


Pap2admlog.jpg

 

  • 3- Click on the Regional tab and look for the Control Timer Values (sec) section.


Regional.jpg

 

  • 4- Enter the desire value in the Interdigit Long Timer field (for example lower this value to 4).


Ctrl timer values.jpg

 

Phone will not ring on handset

Sometimes the Phone you are using is designed for a certain Voltage and Ring Waveform. If someone tries to call you and the phone appears to be ringing for the caller but your phone never rings please follow these steps to hopefully resolve this issue for you.

Step 1: First access the PAP2's web interface.

Step 2: Click on the Admin Login and then click on (switch to advanced view)

Step 3: Click on your Regional Tab on the Top Menu.

Step 4: Go Halfway Down the Page until you see the Heading Ring and Call Waiting Tone Spec


Pap2Ring.jpg

Step 5: Change the Ring Waveform setting to Sinusoid or Trapezoid, the opposite of what you have set. You can also change the Ring Voltage in increments of 5 to 90 or 95.

Step 6: Save Settings and Test an Incoming Call

 

Receiving Unwanted Calls in the middle of the Night ( i.e. CallerID 100) that do not appear in your CDR:

These calls are not going through our Network but rather through the internet directly to your ATA Device.

Please look under the Voice>> Line 1 page in your Linksys device for the following setting: Restrict Source IP and make sure it's enabled.

This way the ATA device will block any traffic not coming from our servers.

RestrictSourceIP.png

Linksys PAP2T ATA Adapter Reset Procedure

Sometimes it will be very helpful to reset your linksys ATA adapter to factory default settings.

  • Connect a telephone to line 1 of the PAP2T unit and power it on.
  • Disconnect your PAP2T adapter from the internet connection(unplug the Ethernet cable from the PAP2T hardware unit). Resetting with internet connection may mess up the unit making it completely useless.
  • Dial ****, and wait for the Interactive Voice Menu (IVM) to get activated.
  • Type in the following number including the # symbol.

73738#

(This number spells RESET.)

  • Confirm this by pressing 1.

Your linksys ATA unit will now go back to it factory default settings.

Note: There are some PAP2/PAP2T devices in circulation which were originally 'locked' to one provider and subsequently unlocked by end users. Do *not* use the RESET$ command with these boxes.

 

See also

 

SPA Star Codes

  • *69 Call Return Code

This code calls the last caller.

  • *07 Call Redial Code

Redials the last number called. (Not in pap2t)

  • *98 Blind Transfer Code

Begins a blind transfer of the current call to the extension specified after the activation code.

  • *66 Call Back Act Code

Starts a callback when the last outbound call is not busy.

  • *86 Call Back Deact Code

Cancels a callback.

  • *05 Call Back Busy Act Code

Starts a callback when the last outbound call is busy. (Not in pap2t)

  • *72 Cfwd All Act Code

Forwards all calls to the extension specified after the activation code.

  • *73 Cfwd All Deact Code

Cancels call forwarding of all calls.

  • *90 Cfwd Busy Act Code

Forwards busy calls to the extension specified after the activation code.

  • *91 Cfwd Busy Deact Code

Cancels call forwarding of busy calls.

  • *92 Cfwd No Ans Act Code

Forwards no-answer calls to the extension specified after the activation code.

  • *93 Cfwd No Ans Deact Code

Cancels call forwarding of no-answer calls.

  • *63 Cfwd Last Act Code

Forwards the last inbound or outbound calls to the extension specified after the activation code.

  • *83 Cfwd Last Deact Code

Cancels call forwarding of the last inbound or outbound calls.

  • *60 Block Last Act Code

Blocks the last inbound call.

  • *80 Block Last Deact Code

Cancels blocking of the last inbound call.

  • *64 Accept Last Act Code

Accepts the last outbound call. It lets the call ring through when do not disturb or call forwarding of all calls are enabled.

  • *84 Accept Last Deact Code

Cancels the code to accept the last outbound call.

  • *56 CW Act Code

Enables call waiting on all calls.

  • *57 CW Deact Code

Disables call waiting on all calls.

  • *71 CW Per Call Act Code

Enables call waiting for the next call.

  • *70 CW Per Call Deact Code

Disables call waiting for the next call.

  • *67 Block CID Act Code

Blocks caller ID on all outbound calls.

  • *68 Block CID Deact Code

Removes caller ID blocking on all outbound calls.

  • *81 Block CID Per Call Act Code

Blocks caller ID on the next outbound call.

  • *82 Block CID Per Call Deact Code

Removes caller ID blocking on the next inbound call.

  • *77 Block ANC Act Code

Blocks all anonymous calls.

  • *87 Block ANC Deact Code

Removes blocking of all anonymous calls.

  • *78 DND Act Code

Enables the do not disturb feature.

  • *79 DND Deact Code

Disables the do not disturb feature.

  • *65 CID Act Code

Enables caller ID generation.

  • *85 CID Deact Code

Disables caller ID generation.

  • *25 CWCID Act Code

Enables call waiting, caller ID generation.

  • *45 CWCID Deact Code

Disables call waiting, caller ID generation.

  • *26 Dist Ring Act Code

Enables the distinctive ringing feature.

  • *46 Dist Ring Deact Code

Disables the distinctive ringing feature. The default is *46.

  • *74 Speed Dial Act Code

Assigns a speed dial number.

  • *16 Secure All Call Act Code

Makes all outbound calls secure.

  • *17 Secure No Call Act Code

Makes all outbound calls not secure.

  • *18 Secure One Call Act Code

Makes the next outbound call secure. (It is redundant if all outbound calls are secure by default.)

  • *19 Secure One Call Deact Code

Secure One Call Deact Code Makes the next outbound call not secure. (It is redundant if all outbound calls are not secure by default.)

  • VoIP Device, PAP2T, Linksys
  • 180 Users Found This Useful
Was this answer helpful?

Related Articles

Cisco SPA112

Make sure to install the latest firmware from Cisco Software. Version 1.3 or later should be...

Dial Plan for Linksys ATAs

The basic dial plan provided in the configuration samples for the Linksys ATA devices (like PAP2,...

Cisco PAP2

Configuration Details Step 1 The first step is to find out what IP Address your adapter is...

Cisco/Linksys Star Codes

The Cisco/Linksys ATA devices come with In-Built star codes that activate certain features on...

Cisco SPA2100

Configuration Details Step 1 The first step is to find out what IP Address your adapter is...