Cisco/Linksys Star Codes

The Cisco/Linksys ATA devices come with In-Built star codes that activate certain features on your device. These features are independent from the features that you can setup from the customer portal, however these will usually be supported by our service.

The following list will provide the most commonly used asterisk codes from your ATA device:

*69 Call Return Code This code calls the last caller.

*07 Call Redial Code Redials the last number called. (Not in pap2t)

*98 Blind Transfer Code Begins a blind transfer of the current call to the extension specified after the activation code.

*66 Call Back Act Code Starts a callback when the last outbound call is not busy.

*86 Call Back Deact Code Cancels a callback.

*05 Call Back Busy Act Code Starts a callback when the last outbound call is busy. (Not in pap2t)

*72 Cfwd All Act Code Forward s all calls to the extension specified after the activation code.

*73 Cfwd All Deact Code Cancels call forwarding of all calls.

*90 Cfwd Busy Act Code Forwards busy calls to the extension specified after the activation code.

*91 Cfwd Busy Deact Code Cancels call forwarding of busy calls.

*92 Cfwd No Ans Act Code Forwards no-answer calls to the extension specified after the activation code.

*93 Cfwd No Ans Deact Code Cancels call forwarding of no-answer calls.

*63 Cfwd Last Act Code Forwards the last inbound or outbound calls to the extension specified after the activation code.

*83 Cfwd Last Deact Code Cancels call forwarding of the last inbound or outbound calls.

*60 Block Last Act Code Blocks the last inbound call.

*80 Block Last Deact Code Cancels blocking of the last inbound call.

*64 Accept Last Act Code Accepts the last outbound call. It lets the call ring through when do not disturb or call forwarding of all calls are enabled.

*84 Accept Last Deact Code Cancels the code to accept the last outbound call.

*56 CW Act Code Enables call waiting on all calls.

*57 CW Deact Code Disables call waiting on all calls.

*71 CW Per Call Act Code Enables call waiting for the next call.

*70 CW Per Call Deact Code Disables call waiting for the next call.

*67 Block CID Act Code Blocks caller ID on all outbound calls. (Note: This differs from the implementation of *67 by some landline providers in that the block remains active until turned off with *68)

*68 Block CID Deact Code Removes caller ID blocking on all outbound calls.

*81 Block CID Per Call Act Code Blocks caller ID on the next outbound call.

*82 Block CID Per Call Deact Code Removes caller ID blocking on the next inbound call.

*77 Block ANC Act Code Blocks all anonymous calls.

*87 Block ANC Deact Code Removes blocking of all anonymous calls.

*78 DND Act Code Enables the do not disturb feature.

*79 DND Deact Code Disables the do not disturb feature.

*65 CID Act Code Enables caller ID generation.

*85 CID Deact Code Disables caller ID generation.

*25 CWCID Act Code Enables call waiting, caller ID generation.

*45 CWCID Deact Code Disables call waiting, caller ID generation.

*26 Dist Ring Act Code Enables the distinctive ringing feature.

*46 Dist Ring Deact Code Disables the distinctive ringing feature. The default is *46.

*74 Speed Dial Act Code Assigns a speed dial number.

*16 Secure All Call Act Code Makes all outbound calls secure.

*17 Secure No Call Act Code Makes all outbound calls not secure.

*18 Secure One Call Act Code Makes the next outbound call secure. (It is redundant if all outbound calls are secure by default.)

*19 Secure One Call Deact Code Makes the next outbound call not secure. (It is redundant if all outbound calls are not secure by default.)

Conference Act Code If this code is specified, the user must enter it before dialing the third party for a conference call. (Your conference call organizer provides you the code.)

Attn-Xfer Act Code If the code is specified, the user must enter it before dialing the third party for a call transfer. (Your telephone administrator must provide you with this code, enabling you to transfer your caller to an outside number.)

*99 Modem Line Toggle Code Toggles the line to a modem. Modem pass-through mode can be triggered only by pre-dialing this code.

*99 FAX Line Toggle Code Toggles the line to a fax machine. (Not in pap2t)

Service Referral Codes Codes used when you place your caller on hold and receive the second dial tone to blind transfer your caller. (Your telephone administrator must provide you with any such codes.)

Dial Feature Codes Codes used when you first receive dial tone. (Your telephone administrator must provide you with any such codes.)

# (2-9) Dial the internal (ata) specified speed dial number. (Add a '#' to end the interdigit timeout.)

  • Codes, Cisco, Linksys, star, Star Codes, Feature Codes
  • 437 Users Found This Useful
Was this answer helpful?

Related Articles

Cisco SPA112

Make sure to install the latest firmware from Cisco Software. Version 1.3 or later should be...

Dial Plan for Linksys ATAs

The basic dial plan provided in the configuration samples for the Linksys ATA devices (like PAP2,...

Cisco PAP2

Configuration Details Step 1 The first step is to find out what IP Address your adapter is...

Cisco PAP2T

If you are running the PAP2t with a tomato firmware router, this may represent a persistent...

Cisco SPA2100

Configuration Details Step 1 The first step is to find out what IP Address your adapter is...